Intelligent Routing Features In PCB Design Software Let You Work Smarter, Not Harder

November 21, 2017 CircuitStudio

Automated Robot learning to solve problems

 

 

Everybody has those lazy moments, trying to figure out how little one can do while still completing a task. In my first job, I created a software where I can automatically launch my favorite applications through voice command. Later, I found a new level by coding a special program to email reports, close applications, and shut down my computer with one click of a button.

 

My first PCB designs took place on the early versions of PCB design software. These had the auto-routing capability; however, I didn’t know how to use them very well yet. I thought, like with my end-of-the-day app, I could just hit a button, go grab some tea, and have the PCB ready for manufacturing when I came back. Yeah, imagine the disappointment when I come back to a poorly routed PCB that I then have to spend hours reworking. It wasn’t very fun.

 

A decade later, PCB design software has gone through many cycles of revision and improvements. Today’s intelligent routing features are much more powerful than their predecessors. But another part to their improving usability is my growing knowledge and experience: PCB software was never meant to replace the skill and insights of a hardware engineer, and so it wasn’t built to do that. Instead, PCB design software, when used appropriately, can save hardware engineers precious time to complete their design. Four key tools can help you leverage intelligent routing protocol features in PCB design software without falling into complacency.

1. Component Auto-Placer

The component auto-placer is a great tool that arranges all your components systematically. It is tempting to just use the auto-placer on most of your components and start the routing process. Indeed, in a simple design, there may not be any major issue. However, in complex applications, failing to separate components according to their modules may cause cross-coupling between noisy components and analog circuits. When cross-coupling occurs, the components end up polluting each other and the system in place, changing an isolated interaction to a more problematic disturbance.

 

Component placement must take into account several factors, including heat production and sensitivity as well as direction and orientation of signals. While it may be possible to have an auto-placer work with these considerations in mind, it is more important to maintain a compatible relationship with the auto-placer. The auto-placer is best used to complement the best practice of component placement.

2. Auto Router

 

Layout of PCB routing

Route smartly through intelligent problem-solving

 
 

Following my—failed—attempt to have the auto-routing feature take over my job, I’ve changed my way of using this intelligent routing tool. Now I use the auto-routing tool to save me countless hours of routing an “unroutable” board.

 

Unroutable boards often occur when your board is too small to hold the number of required connection. When you’re working in this situation, a quick test to save you time is to hit the auto-route and see if it can complete the routing in its first two attempts. If the auto-router fails, then you might need to revise your components or enlarge the PCB size. If you were to attempt this test manually, you could be wasting valuable time. Worse yet is designing before running the auto-route: in that case, you might spend hours on a PCB design just to find that it is impossible to route given its size.

 

One of the best tactics for using auto-routing is to apply it alongside manual and interactive routing. Begin by placing the power supply, high-speed communication, and analog signals manually. Then route the differential pairs before completing the remaining signals with the auto-routing tool. Make sure that the auto-route signal does not alter pre-routed important tracks.  

3. Multiple Pair and Differential Pair Routing

The multiple pair and differential pair routing are great tools in maintaining equal copper length and ensuring they are running in parallel. Instead of routing one signal followed by others, it saves you precious time by routing a set of signals simultaneously. As intelligent as it is, however, it is up to you as the designer to ensure that the differential or multiple pairs signal is not routed near other high speed or analog signals. Consider multiple pair and differential pair routing as tools in your toolbox rather than a replacement for your engineering insights.

4. Design Rule Check

Design rule check (DRC) is probably the best tool that helps engineers to eliminate human errors. It highlights routing errors and zooms into the exact location on the PCB for immediate remedial work. As great as it is, it shouldn’t be the cause of complacency in engineers where PCB best practices are concerned. While it may help eliminate mistakes like unconnected nets or clearance constraints violations, a compatibility with both features and experience will allow the engineer to identify issues like ground loops or incorrect ground plane placement. Ultimately, the DRC is only as effective as the engineer who configures it.

 

Bullhorn reminds you to know the rules

Shortcuts only work if you know what you can’t do first

 

 

Throughout my years designing PCB for various applications, I’ve put intelligent features in various updated versions of CircuitStudio to good use. With the right approach, these features could cut down on your design time without compromising the quality.

 

 

Integrating these tools into your workflow can help you work smarter, not harder. Learn more about intelligent routing features by talking to the experts at Altium.

Previous Article
 Internet of Things Security Best Practices: Passwords, Patches, and Portals
Internet of Things Security Best Practices: Passwords, Patches, and Portals

Hackers love IoT devices because they have poor security. Beef up your defenses with these best practices f...

Next Article
The Advantages and Disadvantages of Active and Passive RFID Technologies
The Advantages and Disadvantages of Active and Passive RFID Technologies

There are 3 main types of RFID, and each comes with its own set of advantages and disadvantages.

Limited Time Offer, Switch to CircuitStudio For $495 !

Buy Now