Are Fiducial Marker Placements on PCBs Still Necessary with Modern Manufacturing Capabilities?

August 28, 2017 CircuitStudio

 

About 10 years ago, I stopped watching horror movies. In my younger days I really enjoyed being scared silly, but when I started my engineering career I became more interested in action and sci-fi genres. This is likely because I was getting my fair share of horror stories at work when simple mistakes resulted in catastrophic post-production nightmares.

 

When I started my electronics design career, through-hole components were extremely popular and surface mounted components were a rare sight. When (Quad Flat Package) QFP packages of microcontrollers (MCU) became popular, I had no choice but to migrate from the old plastic leaded chip carrier (PLCC) footprint. This is because PLCC requires an additional socket while QFP can be mounted on the PCB directly. As far as I could tell, it was only a matter of time before chip manufacturers stopped producing MCU in PLCC packages in favor of QFP or similar packages.

 

When my PCB assembly suppliers dropped me an email stating that they were unable to machine assemble the MCU on the 200 production boards I ordered, my nightmare began. Being accustomed to PLCC sockets, which are through hole components, it didn’t occur to me to provide fiducial markers on the PCB. Failing to do so meant all the QFP packaged MCUs with tiny pitches had to be manually assembled.

 

This resulted in a higher percentage of boards being rejected and countless hours spent fixing faults from imperfect manual soldering. Since then, I make a point of always using fiducial markers in my designs, even if my suppliers tell me that they have upgraded their machines to work without the markers.

 

Electronic components on a circuit
You could end up with a complete mess if you omit fiducial markers.

 

What Is a Fiducial Marker and How Does It Help in Manufacturing

In PCB design, a fiducial marker is a rounded shape of copper that acts as a reference point for pick and place assembly machines. Fiducial pcb markers help machines recognize the orientation of the PCB and its surface mount components with packages that have tiny pitches like Quad Flat Package (QFP), Ball Grid Arrays (BGAs) or Quad Flat No-Lead (QFN).

 

There are two types of fiducial markers commonly found in printed circuit board designs: global fiducial markers and local fiducial markers. Global fiducial markers are a copper reference placed on the edge of the PCB that allows the machine to determine the orientation of the board with respect to the X-Y axis. Placement machines also use the fiducial marker to compensate for any skew when the PCB is clamped.

 

Local fiducial markers are copper markers that are placed outside of the corner of a quad packaged surface mount component. It is used by assembly machines to precisely locate the footprint of a component and reduces errors in component placement. This is especially important when you have fine pitched and large quad packaged components in your design.

 

automation chip mounter working with robo
Always check with your manufacturer for fiducial marker requirements.

 

Are Fiducial Markers Necessary with Modern Manufacturing Technology?

I have always designed my printed circuit boards with both global and local fiducial markers. However, when I came across an article that explained the possibility about omitting local fiducials, I was intrigued. It made sense to remove fiducial markers on smaller PCBs to maximize space for signal traces.

 

As a result of advancements in manufacturing technology, local fiducial markers can be omitted under certain conditions. On smaller boards, modern assembly machines can place SMT components using only global fiducial points. Fiducial markers may also be omitted for components that have a larger pitch. For example, surface mount components with pitches above 1.0mm and above can be placed accurately by the latest machines.

 

That being said, it is important to discuss the extent of your manufacturer’s machine’s capabilities before removing local fiducial markers in your design. I’ve learned the hard way that not all manufacturers are equipped with machines that are powered by the latest technology. On the other hand, global fiducial markers should never be omitted from your designs. Even if you are working with some of the most advanced manufacturing capabilities.  

 

Best Practices for Using Fiducial Markers in PCB Design

If you want to get the best out of machine assembly, you need to get your fiducial markers right. There are few important guidelines when it comes to placing fiducial marker in your design.

 

  1. The fiducial marker is made by placing a non-drilled copper layer in a circular shape. The fiducial marker must be free from solder mask.

  2. The optimum size of a fiducial marker should be between 1mm and 3mm. A clearance area similar to the diameter of the marker must be maintained.

  3. For global fiducials, 3 markers are placed on the edge of the boards for the best accuracy. In cases where there is insufficient space, at least 1 global fiducial marker is required.

  4. The fiducial marker must maintain a distance of 0.3 inches to the edge of the board, excluding the clearance area of the fiducial marker.

  5. For local fiducial, place at least two fiducial markers diagonally on the outside edge of the surface mounted component.

 

Using professional PCB design software, like Altium’s CircuitStudio, a fiducial marker can be placed by inserting a pad, changing the pad size to zero, and setting the correct values for the diameter.


Need more tips in placing fiducial markers on your design? Contact an expert at Altium.

 

 

Check out Altium Designer in action...

Modern Interface Experience

 

Share your feedback in the comments below and remember to share.

Previous Article
Why Designing a High Voltage PCB for Rapid Prototyping Is More Effective Than Rushing to Form Factor
Why Designing a High Voltage PCB for Rapid Prototyping Is More Effective Than Rushing to Form Factor

Troubleshooting your circuit designs before they are in form factor will save you more time in the long-run.

Next Article
Conducted Emissions Test Equipment and Reduction Guidelines
Conducted Emissions Test Equipment and Reduction Guidelines

Why wait for official labs to reject your product for conducted EMI? Get your own equipment and solve desig...

×

...or download the PDF to keep learning offline

First Name
Last Name
State
Country
Acknowledging Altium’s Privacy Policy, I consent that Altium processes my Personal Data to send me communications, including for marketing purposes, via email and to contact me by phone.
Postal Code
!
Thank you!
Error - something went wrong!