Competition for HDI: VeCS

March 7, 2019 Happy Holden

Not long ago, a very creative engineer in Europe proposed a novel concept for layer-to-layer connections that has higher density than the conventional through-hole. That engineer is Joan Torne’ of NEXTGin Technologies BV [1] and his technology is called, “Vertical Conductive Structures-VeCS”. It employs the conventional PCB TH fab equipment, increases densities to that of HDI, with capabilities down to 0.4 mm pitch BGAs.

The concept is to peck-drill or route a slot or cavity into the board (for blind connections) or through the board, then metallize and plate. In the final fabrication step, slightly larger holes are drilled that creates a vertical connection between layers, as seen in Figure 1 a.  As you can see from the illustration in Figure 1b, these smaller vertical connections take up less room than a conventional drilled through-hole, thus allowing more space for routing. In the example I created in Figure 1c, I compared TH, microvias and VeCS for a 1.0 mm pitch BGA. For the TH, you can squeeze 2-tracks under the dog-bone breakouts, while using swing-microvias, you can achieve 7-tracks. Equally as dense is the VeCS breakouts with 7-tracks. When dropping to 0.5 mm pitch BGAs, for TH, there is no room to route more than one-track through, if using via-in-pad, but for HDI, you can route 7 tracks between the blind-vias. VeCS is almost as dense with the ability to route 5-tracks between the vertical connections. For the larger pitches, there is some flexibility with VeCS breakout, as seen in the 1.0 mm with two different routing into the cavity.

FIGURE 1. a. The VeCS technology creates vertical traces to connect layers together rather than employing an entire hole; b. A 3D view  shows the advantage of additional routing space created by using only the vertical wall; c. A comparison of the two common technologies, TH and HDI versus VeCS for two BGA breakouts-1.0 mm and 0.5 mm BGAs.

The routing rules for Figure 1c are shown in Table 1:

TABLE 1. Design and routing rules for the two BGA breakouts and routings for through-hole, HDI-microvias and VeCS technology

The VeCS manufacturing process hasn’t changed the conventional multilayer manufacturing process, just a few additional steps have been added:

1. Drill or route a slot between BGA lands

2. Metallize as normal

3. Image with VeCS breakouts adjacent to the metallized slot

4. Plate as normal

5. Strip and etch as normal

6. At final fabrication, drill out the metallization for vertical traces

The process (seen in Figure 2) does not require the use of a laser drill and is compatible with a panel plate process.

FIGURE 2. The VeCS fabrication process is very conventional

The only article published on the technology, The PCB magazine-February 2017 [2], indicated Joan had created test vehicles to test reliability and used Altium Designer® to create the artwork. The fabrication and testing were done by WUS. After multiple lead-free reflow cycles and thermal cycling to failure-results were comparable with through-holes. Signal integrity appears to be slightly better as the vertical trace has less inductance than a hole, but the slots or cavities may interfere with ground pours.

For the cost trade-offs, the increase routing density will hopefully allow fewer signal and reference layers or a smaller board with more-up per panel. Thus, saving money and paying for the one-up drilling or routing process to create the cavities or slots in the board.

If this is a concept that you might use, contact your favorite PCB fabricator to try a test board. If you want to use it in a design, contact NEXTGin [1] to see about the patent status of the technology.  NEXTGin report two PCB fabricators are currently using the technology.

 

REFERENCES

  1. https://www.nextgin-tech.com/
  2. Starkey, Pete, Interview of Joan Tourne’, “Vertical Conductive Structures–a New Dimension in High-Density Printed Circuit Interconnect”, The PCB magazine, February 2017, pp 16-20

About the Author

Happy Holden


Happy Holden is retired from GENTEX Corporation (one of the U.S.'s largest automotive electronics OEM. He was the Chief Technical Officer for the world’s biggest PCB Fabricator-HonHai Precision Industries (Foxconn) in China.

Prior to Foxconn, Mr. Holden was the Senior PCB Technologist for Mentor Graphics; he was the Advanced Technology Manager at NanYa/Westwood Associates and Merix Corporations. He retired from Hewlett-Packard after over 28 years.

His prior assignments had been as director of PCB R&D and Manufacturing Engineering Manager. While at HP, he managed PCB design, PCB partnerships, and automation software in Taiwan and Hong Kong.

Happy has been involved in advanced PCB technologies for over 47 years. He has published chapters on HDI technology in 4 books, as well as his own book, the HDI Handbook, available as a free e-Book at http://hdihandbook.com and de recently completed the 7th Edition of McGraw-Hill's PC Handbook with Clyde Coombs.

Follow on Linkedin Visit Website More Content by Happy Holden
Previous Article
Routing Topologies in Your PCB and Computer Peripherals
Routing Topologies in Your PCB and Computer Peripherals

With the alphabet soup of computer peripherals comes routing topologies. Learn how to mix and match in this...

Next Article
HDI Quality and Acceptability Requirements
HDI Quality and Acceptability Requirements

Learn about Vendor Qualification when selecting an HDI fabricator here.

×

Trade In Your Outdated Design Tool & Unlock 45% Off Altium Designer. Sign up and an Altium representative will be in contact shortly.

First Name
Last Name
Company Name
Phone Number
Country
State
Postal Code
Acknowledging Altium’s Privacy Policy, I consent that Altium processes my Personal Data to send me communications, including for marketing purposes, via email and to contact me by phone.
!
Thank you!
Error - something went wrong!