Flexible Circuit Base Materials

Tara Dunn
|  Created: March 4, 2019  |  Updated: July 27, 2020
Flexible Circuit Base Materials

Question:  As someone new to designing with flex materials, what is important to understand about the base materials?

For people new to calling out flex materials, it can be a little intimidating. Just like their rigid material counterparts, there are so many options to choose from, it can be mind-boggling. But, also just like their rigid material counterparts, once you learn the “basics”, most designs will fit within common parameters. Once those basics are understood, the special circumstances can more easily be handled.     

For this blog post, I will talk about flex-only constructions to help narrow the focus and we can dive into rigid flex material considerations in a future blog post.  Although there are many flexible materials, let’s start with the most common: adhesiveless laminate constructions with copper and adhesiveless polyimide. 

There are two primary constructions for flex base materials, adhesive-based materials and adhesiveness.  Both are typically supplied with a layer of rolled-annealed copper and a layer of adhesiveless polyimide. Adhesive-based materials can be spec’d with either standard acrylic adhesive or flame retardant acrylic adhesive, depending on the end application requirements.  

First, what is the difference between rolled annealed copper and electrodeposited copper?

Rigid materials are typically manufactured with electrodeposited (ED) copper. ED copper is formed by electrolytic deposition onto a slowly rotating polished drum from a copper-sulfate solution. When an electric field is applied, copper is deposited on the drum as it rotates at a very slow pace; the slower the pace, the thicker the copper. The side against the drum provides a smoother finish.                                               

Flexible laminates are typically constructed with rolled annealed copper. Rolled annealed (RA) copper foils are created by successively passing an ingot of solid copper through a rolling mill, and then applying high temperature to anneal the copper. RA copper foil has higher ductility and elongation than ED copper which is why it is best for bending applications. 

When would you select adhesiveless materials instead of adhesive-based materials?

Adhesive-based materials are the workhorse of flexible circuit materials, especially for flex-only applications. They have been used for decades and are most commonly used in single and double-sided designs. These materials are typically lower cost than adhesiveless materials, and doesn’t that seem crazy? There is more material involved, but it is less expensive.  

A typical adhesive-based laminate will be constructed with a layer of copper, a layer of 1 mil adhesive, a layer of polyimide, another layer of adhesive, and a second layer of copper.  

Adhesiveless material, as you would expect, eliminates the adhesive layers and typically reduces that double-sided laminate by 2 mils. 

 Adhesiveless materials are most commonly spec’d when the design is a higher layer count flex or a rigid-flex construction. In both cases, adhesiveless material is recommended for quality and reliability reasons. The z-axis expansion rate of the acrylic adhesive is a concern for plated-through-hole integrity. In higher layer count, flex-only applications, there is also a material thickness concern. Eliminating 1 mil of adhesive thickness per copper layer can significantly decrease the overall thickness and increase flexibility in the final product.     

What material constructions are available?

There are so many material constructions available. Copper is typically available from ¼ ounce to 2 ounces. This doesn’t mean that you can’t have copper thicker than 2 ounces, it simply means that your fabricator would need to create that adhesiveless laminate with raw copper, adhesive, and polyimide, rather than purchasing a pre-made laminate. Adhesive thicknesses range from half mil to 2 mil. Polyimide thicknesses range from half mil to 5 mil. You can literally purchase nearly any combination of these materials and thickness if you have a specific end-use requirement.  

What material constructions are most common and most available?

Just because you can spec in any combination of material thicknesses, doesn’t mean that is necessarily the best approach. If you are looking for the common constructions to help reduce both cost and lead time associated with a special order, try to stick to constructions with 1 mil adhesive (if you are selecting adhesive-based materials), and a combination of ½ oz or 1 oz copper and 1 or 2 mil polyimide. These constructions are typically the most common constructions which often means lower cost and shorter lead times to procure the material supplier and will help keep costs down with your flex stack up.   

What are more important than common material constructions to keep costs down?

Now that I have explained what the most common materials are, which should be materials that are most readily available and lower cost, there is one more critical piece to this.  That is, what material does your preferred fabricator stock? At the end of the day, each fabricator has a material set that they commonly stock and that will have a meaningful impact on your material costs and lead time. Let me explain. Adhesive-based materials are less expensive than adhesiveless materials. But, if your fabricator manufacturers a significant percentage of rigid-flex or higher layer count flex, they will likely purchase more adhesiveless material, which reduces costs, and will likely have more of the adhesiveless material in stock, which reduces lead time.  My best recommendation? Work with your fabricator early in the design process. Most fabricators are happy to supply a stack-up for you. If you specifically ask for their more common materials, you can ensure materials that do not require a special order and should not require an extended lead time. 

Questions?

Future blog posts will dive into rigid-flex material considerations and tips to ensure that the material set you select, along with your design, meet flex material design guidelines. I would love to hear your specific questions. Leave a comment and we will be sure to address it!

About Author

About Author

Tara is a recognized industry expert with more than 20 years of experience working with: PCB engineers, designers, fabricators, sourcing organizations, and printed circuit board users. Her expertise is in flex and rigid-flex, additive technology, and quick-turn projects. She is one of the industry's top resources to get up to speed quickly on a range of subjects through her technical reference site PCBadvisor.com and contributes regularly to industry events as a speaker, writes a column in the magazine PCB007.com, and hosts Geek-a-palooza.com. Her business Omni PCB is known for its same day response and the ability to fulfill projects based on unique specifications: lead time, technology and volume.

Related Resources

Related Technical Documentation

Back to Home
Thank you, you are now subscribed to updates.