Slaying the PCB 90⁰ Right-Angles Bend Dragon

Kella Knack
|  Created: March 24, 2019  |  Updated: April 15, 2020

As anyone designing PCBs knows, there are a lot of “Rules-of-Thumb” and myths that have populated the industry. One of the areas where misinformation continues to abound focuses on 90° angle bends in PCB traces. A pretty good job has been done to address some of the most outlandish aspects of the bad data such as avoiding right-angle bends because electrons would go flying off the corners and not using them because the copper in the corners can flake off (although it should be noted that a recent search on the Internet yielded yet another iteration of the copper-flaking myth).

There are two areas where correcting the right-angle bend myth continue to remain “fuzzy”: Signal Integrity (SI) and Electromagnetic Magnetic Interference (EMI) Electromagnetic Interference (EMI). This blog will focus on these two areas. Further on, empirical information will be presented that proves why the following assumptions are erroneous.

SI

First assumption:

  • When you are designing high-power PCB transmission lines at RF frequencies, you are involved with circuits that use trace widths of 100 mils and, as a result, you need to worry about 90° angles. The assumption is that the extra width in the corner is capacitance that can cause an impedance variation which can lead to reflections, signal distortions and noise along the trace. This is simply not true. Rather, this is a concept borrowed from RF and microwave design guides used in the development of high-power RF circuits. In a megawatt transmitter you have thousands of volts. If you have right-angle bends, there is corona discharge caused by sharp points. This does not occur in low-power PCB implementations such as logic circuits.

Second assumption:

  • It is safe to use right-angle tracks in your design as long as you are not working on ultra-high frequency microwave designs. The truth is that frequency is not an issue of concern. If you examine the impedance between a 45° degree track and a right-angle bend, you cannot tell the difference between the two. The signal does not either. Evidence presented below shows this is not so.

EMI

The assumption:

  • With right-angle bends, electronic fields become concentrated at the corners. This results in destructive electromagnetic radiation coming from those corners that manifests itself as EMI. Evidence presented below shows this is not so.

The Proof is in the Test Results

To validate the claims made regarding the impact of right-angle bends, a 16-layer test PCB containing more than one hundred different test structures was built to address the long-held impedance and EMI claims. That board is depicted in Figure 1.

Figure 1. Layer Artwork of Test PCB

Trace 15 has a right-angle bend near each end. Traces 24 and 25 have right-angle bends in them in their lower right-hand corners. To test these three traces, a Time Domain Reflectometer (TDR) with a rising edge of 125 picoseconds was used to determine if these right-angle bends cause any change in impedance. If there is any meaningful degradation from these bends, there should be a detectable change in impedance that is visible on the TDR trace. A lowering of impedance would be depicted as a reflection that is “negative” going. A rise in impedance would be depicted as a reflection that is “positive” going.

Figure 2 contains the three TDR plots for the three test traces. The first dip in impedance is where the test cable makes contact with one end of the trace at a via. The second dip in impedance is the test via at the opposite end of the trace. The flat portion between these two dips is the trace under test.

Figure 2. TDR Records of Three Traces with Right Angle Bends

It can be seen from these tested traces that the right-angle bends caused no detectable change in impedance even with an edge of 125 picoseconds. In a related test PCB, done by a group of engineers and tested at the University of Missouri, Rolla, a right-angle bend was tested with an 18 picosecond edge and the same results were achieved. In that same test, as reported in Printed Circuit Design Magazine, titled “90° Corners, The Final Turn,” by Douglas Brooks, (January 1998), right-angle and acute-angle bends were tested for reflections and as potential sources of EMI with negative results.

If one closely examines a right-angle bend, it can be determined that for a very short distance, the effective width of the trace is wider. However, for such a short distance, there is no detectable change in either Co (parasitic capacitance) or Lo (parasitic inductance). These two variables have to be affected in order for a reflection to occur. This particular myth arose as a result of one particular figure (Figure 7-17) appearing on one particular page (page 144) of the Motorola ECL Systems Handbook that was published in 1973. This figure shows two traces, side-by-side, one with two right-angle bends and the other with those bends rounded. Below that picture are two oscilloscope traces. The trace for the right-angle bend example has two small dips in the middle of it while the trace for the rounded corners has none. This suggests that right angle-bends cause a problem. Backing up to page 140 of the handbook, Figure 17-4, shows a trace with two right-angle bends and no disturbance at all from either one of the bends. It turns out that Figure 7-17 was flawed and should not have been published. It led to the unfortunate prevention of right-angle bends that should never have been promulgated in the PCB design and manufacturing arenas.

The Manufacturability Consideration

In addition to the foregoing, there is one final argument to consider regarding right-angle bends and that deals with PCB manufacturability. The assumption was that right-angle or sharp angle bends used to present a realistic threat to manufacturability. Sharp corners would create acid traps and these acids would corrode the copper in the sharp corners. The realty is if there were acid trapped anywhere on a copper layer, it would cause leakage problems later in the process so PCB fabricators made sure the rinse operations did not leave any acids or other chemicals anywhere on a PCB.  Further, in the early days of PCB fabrication, there was a problem with the process used to image PCB copper layers for etching. The first process used was silk screening not unlike the process used to put an image on a T-shirt. When there were right angles or acute angles in the copper, the ink from the silk screen would often bleed into the tight corner leaving an unattractive looking feature when etching was completed. This only caused cosmetic problems not electrical ones. Inspectors would often reject PCBs with this type of blemish because they did not look right. The simplest way to avoid these rejects was to prevent this kind of junction between two pieces of copper. It’s quite likely that this rule morphed into the acid trap rule that is still sometimes being passed around the industry.

It was also assumed that right-angle corners weren’t as sturdy as 45° ones and could be peeled off easily (note the statement at the beginning of the article regarding copper flaking). The reality is that right-angle bends are no less robust from a structural standpoint than rounded corners.

The key takeaway here is avoiding 90 degree angle bends in PCB traces is not relevant.You have only to look at other elements within a PCB design to see that this is true. Traces turning and going up a via have right-angle bends. Also, if you lift the lid off an IC you will see that the tracks have right-angle bends.  Most importantly, if you waste a nanosecond in making right-angle bends on your PCB traces go away, you are wasting your company’s money and making your designs far more complicated than they need be.

References:

  1. Ritchey, Lee W. and Zasio, John J.,  “Right The First Time, A Practical Handbook on High-Speed PCB and System Design, Volume 1.”

  2. Brooks, Douglas. “90 Degree Corners, The Final Turn,” Printed Circuit Design, January 1998.

About Author

About Author

Kella Knack is Vice President of Marketing for Speeding Edge, a company engaged in training, consulting and publishing on high speed design topics such as signal integrity analysis, PCB Design ad EMI control. Previously, she served as a marketing consultant for a broad spectrum of high-tech companies ranging from start-ups to multibillion dollar corporations. She also served as editor for various electronic trade publications covering the PCB, networking and EDA market sectors.

Related Resources

Back to Home
Thank you, you are now subscribed to updates.