Practice Makes Perfect: How to Test Electronic Components during PCB Design

February 8, 2018 Altium Designer

Basketball and hoop on sky background

 

 

When I was younger, well much younger, I had dreams of one day being a pro athlete. I wanted to be the guy who scored the winning touchdown, knocked in the winning run or hit the buzzer-beater. Although I never made to the professional level, I did have some success and I learned a lot. The most important thing was the results you achieved were strictly tied to your preparation. In other words, if I wanted to do well in the game I had to test myself by practicing.

 

I’m still using those skills, though: in order for your PCB to function as intended, you need to test your design. By testing the electronic components of your board before manufacturing you can be sure that it will perform as you intended with your design.

 

The most successful teams that I played on had coaches who stressed the importance of practicing as if you were playing in an actual game. It is one thing to shoot baskets alone, but it is something else to make them when you are being defended. The same difference exists between simulating your circuit’s schematic without the physical and material restrictions of the actual board and testing your electronic components during PCB design.

Is Testing PCB Components During Design Necessary?

Although this is a very important design step, schematic simulation does not guarantee the functionality, reliability or even manufacturability of your design. Applying good design for manufacturing (DFM) practices will help you ensure that your design can be manufactured. However, there are additional steps you can take to test functionality and reliability during design.

 

The reasons for performing a schematic simulation of your circuit are to:

Determine Component Parameters: Primarily voltages, currents, and impedances.

Verify Circuit/System Operation: Check inputs/outputs, and signal levels.

Make Changes and Correct Errors: Replace parts, or make design changes.

Save Costs: By not having to buy components or materials for testing.

 

But what if you knew that one of your board's electronic components would fail at some point once it is in the field? You would either replace the component or change your design to remove the source of the failure before manufacturing the board. A design tool like a power distribution network analyzer (PDNA) allows you to evaluate parameters of your PCB as if you were using electronics testing equipment on the actual board.

 

 PCB with multimeter

You can condense your design rule checking into a smooth operation within your layout software.

 

Performing tests on your PCB electronic components during design will not only make sure that your boards will function properly and be reliable but also save costs if changes have to be made.

How to Test PCB Components During Design

The use of a PDNA provides a united design and analysis environment for your PCB design. You can perform power distribution analysis over the entire board or only specify predefined areas. Additionally, voltage gradient overlays give the power to look at voltage drops on the ends of all traces; including vias. You can also look at current density on your traces to make sure there are no potential undercurrent/overcurrent issues.

 

This ability to look at a component’s incoming and outgoing traces can be used to determine the component’s specific parameters. Employing these capabilities during design is akin to a successful practice where you can follow it up by moving to fabrication and assembly confident that your board will perform as designed.

 

boy and coach high-fiving

Successfully practice your PCB design without ever leaving your layout software.

 

 

The ability to gather thermal, signal, and power integrity, current density, and trace impedances during design is a significant benefit to the PCB design process. Not only are you able to perform design for manufacturing (DFM) checks, but you can also test the board’s electronic components, both of which can save development time. With the right PCB design software such as Altium designer, PDNA and other smooth design methodologies are available to you.


For more information and tips on testing electronic components during PCB design and how to make corrections that will avoid post manufacturing problems, contact an Altium PCB design expert.

About the Author

Altium Designer

PCB Design Tools for Electronics Design and DFM. Information for EDA Leaders.

More Content by Altium Designer
Previous Article
Properties of Semiconductors: Electrodeposition and PCB Devices
Properties of Semiconductors: Electrodeposition and PCB Devices

If you’re looking to innovate even further with your PCB designs, knowing the properties of semiconductors ...

Next Article
Designing Operational Amplifiers: PCB Layout Tips to Reduce the Noise
Designing Operational Amplifiers: PCB Layout Tips to Reduce the Noise

Operational amplifiers are great tools for your PCB design; however, during PCB layout you’ll need some tip...

Get My Altium Designer Free Trial Today or Call 1-800-544-4186

Get Free Trial