Stripline vs Microstrip: Understanding Their Differences and Their PCB Routing Guidelines

September 22, 2017 Altium Designer

Untitled design (25).jpg

 

The first time I heard a presentation on high speed design techniques, it went straight over my head. Since this was at the beginning of my career as a designer, I’m sure that it was my inexperience that caused the confusion. The whole concept of stripline and microstrip routing didn’t make any sense to me and I thought that the instructor was talking about a completely different type of PCB designs that I wasn’t familiar with. Fortunately, my confusion was quickly straightened out when I learned that it isn’t the PCB schematic itself that is considered to be stripline or microstrip. Instead, stripline and microstrip are different methods of routing high speed transmission lines on a PCB design.

 

Understanding stripline and microstrip can be difficult. So whether you are new to PCB design schematic or if you are looking for a refresher on the topic, this basic review is for you.

 

Human and drawing PCB circuit

Understanding Stripline and Microstrip

 

 

Stripline and microstrip, what are they?

Stripline and microstrip are methods of routing high speed transmission lines on your PCB design. Stripline is a transmission line trace surrounded by dielectric material suspended between two ground planes on internal layers of a printed circuit board. Microstrip routing is a transmission line trace routed on an external layer of the board. Because of this, it is separated from a single ground plane by a dielectric material.

 

With the transmission line on the surface layer of the board, microstrip routing has better signal characteristics than stripline. Circuit board fabrication is also less expensive with microstrip since the layer structure of one plane and one signal layer makes the manufacturing process simpler. Stripline can be more complex to manufacture because is requires multiple layers to support the embedded trace between two ground planes. However, the width of a controlled impedance trace in stripline is less than an impedance trace in microstrip of the same value. This is because of the second ground plane. These smaller trace widths enable greater circuit densities, which in turn enables a more compact design. The internal layer routing of stripline also reduces EMI and provides better hazard protection.

 

Stripline and microstrip have different benefits. The decision of which is the better method should be based on the needs of the design. In a dense high speed design, a mixture of both methods on a multi-layer circuit board is often used to accomplish the design goals.

 

Furthermore, it is extremely important to maintain controlled impedance across the design when routing transmission lines on a high speed design. The layer of the PCB that the transmission line is routed on, the physical characteristics of the transmission line trace, and the characteristics of the dielectric all need to be calculated together in order to give the correct impedance values for the circuit. There are many different impedance calculators with different stripline and microstrip models that are available for making these calculations.

 

Picture of different types of transmission line routing

Stripline and microstrip routing are important to consider for your PCB design

 

 

Examples of stripline and microstrip routing

The following are some examples of stripline and microstrip routing techniques and how some of their characteristics affect their impedance calculations:

 

  1. Microstrip. Transmission lines that are routed on the external layers are considered to be microstrip. The model for these is based on the trace thickness and width, and the substrate height and dielectric type.

  2. Edge-Coupled Microstrip. This technique is used for routing differential pairs. It is the same structure as regular microstrip routing, but the model is more complex with the addition of the trace spacing for the differential pair.

  3. Embedded Microstrip. This structure is similar to regular microstrip except that there is another layer of dielectric above the transmission line. Soldermask can be considered as a layer of dielectric and must be accounted for in the impedance calculation.

  4. Symmetric Stripline. Transmission lines that are routed on internal layers (between two ground planes) are considered to be symmetric stripline, or just plain “stripline” routing. Like microstrip, their model is based on the trace thickness and width, and the substrate height and the dielectric type with the calculation adjusted for the trace being embedded between the two planes.

  5. Asymmetric Stripline. Although similar in structure to the symmetric stripline model, this model accounts for the transmission line trace that is not balanced precisely between the two planes.

  6. Edge-Coupled Stripline. This technique is used for routing internal layer differential pairs. It is the same structure as regular stripline, but the model is more complex with the addition of the trace spacing for the differential pair.

  7. Broadside-Coupled Stripline. This technique is also used for routing internal layer differential pairs, but instead of side by side, the pairs are stacked on top of each other. The model is similar as for edge-coupled stripline.

 

I hope that this tutorial on stripline and microstrip has been helpful in clearing up some of the confusion surrounding these concepts. Understanding what the different stripline and microstrip methods of routing transmission lines are will ultimately help you to design a better high speed board.


Would you like to find out more about high speed design and how your CAD layout software can help you to achieve success? Talk to an expert at Altium.

 

Check out Altium Designer in action...

Powerful PCB Design

About the Author

Altium Designer

PCB Design Tools for Electronics Design and DFM. Information for EDA Leaders.

Visit Website More Content by Altium Designer
Previous Article
High Speed PCB Design Considerations: Component Shape Considerations
High Speed PCB Design Considerations: Component Shape Considerations

Some practical tips for enhancing the component footprint and pad shapes on your high speed PCB design.

Next Article
Facial Recognition and Its Applications in the Internet of Things and Wearables
Facial Recognition and Its Applications in the Internet of Things and Wearables

The Internet of Things and wearables markets could use facial recognition to give their users a much bette...