Preventing Ground Loops in Your PCB Design

April 11, 2018 Altium Designer

Proper signal trace routing can prevent ground loops

I think we’ve all been there. You buy that awesome stereo system only to hear that familiar humming sound in the background. When you take it back to the store the clerk blames the manufacturer. The stereo manufacturer then blames the component manufacturer and the component manufacturer can’t blame anyone. In reality, ground loops that form due to shoddy design are the source of the problem.

Ground loops generate noise in electric circuits. Large currents can exist in ground planes, and a voltage differential between ground connections causes the formation of a ground loop. Ringing or humming sounds in some audio systems are just one manifestation of ground loop noise.


Why Does Ground Routing Matter Anyways?

If you remember your Electronics 101 class, you know that all electric currents move around closed loops. On a PCB ground loop, signals are routed around the board using signal and nearby return traces. As the signal rises to full strength and moves through the board, it tries to induce a return signal in the nearby return trace. In other words, the signal and return traces create a current loop, and the strength of the induced return increases with smaller loop area.

So why is this important? This means that if you want to ensure a reliable return signal to ground, your signal and return traces should be placed as close together as possible. As the signal traces are typically mounted at the top of the board, it is natural to route return traces directly underneath signal traces. This helps reduce EMI by keeping circuit loop areas to a minimum with a pcb layout.


Ground Plane Connections

Rather than route signal and return traces directly on top of each other, you can place a conducting plane below signal traces and ground it. By placing this ground plane below signal traces, the return signal will naturally be induced below the signal trace and your circuit will be complete.

When the ground plane is placed directly below the plane containing your signal traces, all of your signal traces will induce their own return trace directly in the ground plane. This should illustrate the convenience of using a large ground plane to route return signals rather than routing return traces individually.

No ground plane is a perfect conductor; it has some resistance and inductance. If two signal traces connect to the ground plane at different points, a small voltage differential can exist between these two connections. This is a major source of PCB ground loops in the ground plane. Ground loop and return path potentials tend to be on the order of microvolts, but this is still enough to cause signal integrity problems, especially in low current devices.

PCB schematic and finished board

Proper planning can mitigate several potential ground loop problems

While noise that arises due to ground loops can never be completely eliminated, it can be significantly reduced such that its effects on signal integrity are minimized. Rather than connecting ground connections at different points, it is better to route traces to a ground connection with the ground plane. This minimizes any potential differential between PCB traces ground plane connections by simply reducing the distance between them.

The ground return to the power supply should also be connected to a ground plane at a single point. When a ground plane is connected to the power supply only at a single point, the entire ground plane will be held at nearly the same potential. If the ground plane is connected to the power supply return at multiple points, ground loops can form due to the voltage differential between these connections. Using a single and proper grounding connection point eliminates these loops.


The Right Topology

Unfortunately, only simpler designs with low component interconnectivity will allow placement of a ground plane that spans below every signal trace. Spanning a ground plane below signal traces is generally a good idea in lower frequency devices. Keeping the area enclosed by your signal traces and the ground plane small also reduces susceptibility to external EMI.

Spanning the large ground plane under every component may not even be desirable in high-frequency applications. For example, in high-frequency mixed-signal circuits driven by crystal oscillators, placing a ground plane directly below the signal clock creates a center-fed patch antenna. This will actually exacerbate EMI issues, and signal integrity is likely to be degraded without significant shielding.

If you elect to use multiple ground planes, ground loops can be prevented between ground planes by using the proper topology. Rather than connecting ground planes in a ring-like or daisy-chain topology, ground planes can be connected to the power supply ground in a star topology. Daisy chaining your ground planes creates can cause ground loops between ground planes. A star topology connects each plane directly to the power supply and eliminates loops between ground planes.

Metallic spheres connected in a start-type-shape

Use a star topology to connect multiple ground planes

When multiple ground planes are used in your design, take care to avoid routing traces over multiple ground planes. Traces should only be routed over their own ground plane. This is especially important in mixed-signal design. For example, if a digital signal is routed over an analog ground plane, noise coupling can occur between the digital and analog signals. This defeats the entire purpose of the star topology.

The PDN Analyzer™ tool in Altium Designer® allows you to optimize your design so that signal integrity issues are minimized. Furthermore, the 3D PCB design interface can certainly help visualize your designs. To find out more, talk to an Altium expert today.

About the Author

Altium Designer

PCB Design Tools for Electronics Design and DFM. Information for EDA Leaders.

Visit Website More Content by Altium Designer
Previous Article
GPS Antennas in Your PCB Design: You Won’t Get Lost Again
GPS Antennas in Your PCB Design: You Won’t Get Lost Again

If you want functioning GPS, you can add it on your PCB through antenna design and other signal integrity t...

Next Article
With RF Circuit Impedance in Mind Your Designs Won't Look Bird-Brained
With RF Circuit Impedance in Mind Your Designs Won't Look Bird-Brained

For RF circuits, impedance can be a real hassle to work through. With this understanding of the causes of i...