Termination Methods in High Speed and High Frequency PCBs

Zachariah Peterson
|  Created: September 16, 2018  |  Updated: November 16, 2023
Termination Methods in High Speed and High Frequency PCBs

The topic of termination will inevitably come up when dealing with high-speed digital systems. Most digital systems have at least one standardized high-speed interface, or possibly fast GPIOs that produce fast edge rate signals. Advanced systems will have many standardized interfaces which also have termination applied, normally on the semiconductor die. If you determine that you actually need termination, what method should be used?

As it turns out, application of discrete terminators is not very common in most digital systems because so many components implement standardized buses for digital communication. But if you are dealing with advanced components that have fast I/Os, then you might need to manually apply termination with discrete components. The other instance where this arises is with specialty logic, such as is sometimes used in certain processors and FPGAs. Finally, there is the matter of RF termination, which is very different from termination digital systems.

When and How to Apply Termination

As was mentioned above, there is a narrow range of cases where termination with discrete components needs to be manually applied.

  • Your interface does not have an impedance specification
  • Your data sheets state that manual termination is needed
  • Your interface specification demands specific termination (e.g., DDR, Bob Smith termination in Ethernet)

RF and digital impedance matching are somewhat different. Overall, the goal is the same: the signal sent into a transmission line should experience minimal loss during propagation and be registered at the correct voltage/power level by the receiving component. The table below compares termination methods used in digital and RF:

 

 

Digital channel

RF channel

Termination bandwidth

Requires broadband termination circuit

Requires narrowband termination circuit

Power loss

Some power loss is acceptable in certain cases

Prefer to have no power loss in the passband

Applicable range

Circuit designs work up to few GHz bandwidths

Circuit designs are accurate up to few GHz

Standardization

Usually On-die in standardized interfaces

High GHz components place termination on-die

 

The next point to understand is the proper selection of a termination method for your particular system. The sections below provide brief overviews and links to resources about the various types of terminations that can be used in single ended, differential, and RF interconnects.

Series Termination

This termination method involves placing a series resistor right at the driver's output pin. Technically, transmission lines are linear systems and a series resistor could be put anywhere along the interconnect. However, it is preferable to place the series resistor right at the driver output as this provides most accurate scaling of the output signal and the correct reflection suppression.

Series resistor values needed for termination can be difficult to determine as the required data is not always present in a datasheet. Instead, it needs to be determined from a known good IBIS model for the driving pin, or it needs to be determined through measurement. Therefore, it is sometimes more desirable to use parallel termination.

Parallel Termination

Parallel termination is used to suppress reflection off of a receiver while also ensuring the full scale voltage is received by the load’s input pin. Therefore, it needs to be placed right at the input pin on the load component, and the value of the resistor is set to be equal to the transmission line’s impedance.

In some special cases, parallel termination and series termination can be used together on the same interconnect, but this is not common. This is more often found in specialty logic, where the output signal level may need to be intentionally shifted down to a lower voltage, but not necessarily with a perfectly matched series resistor. Another instance is where a designer attempts to suppress ground bounce by placing a series resistor for damping, but the reflection off the load is still suppressed with parallel termination.

Thevenin, Pull-Up, and AC Termination

Thevenin termination, pull-up termination, and AC termination are all types of parallel terminations applied at the input pin of a receiving component. They essentially perform the same function as simple parallel termination with a resistor, but with some additional consequences.

  • Thevenin - adjusts the voltage level and draws power from an alternative supply voltage
  • Pull-up - forces signal to switch around some terminating voltage level; can be used for logic inversion
  • AC termination - limits channel bandwidth to lower frequencies and provides a filtering function
Termination methods parallel

Among these three types of terminations, Thevenin and pull-up are used more often. You are more likely to see these implemented on the semiconductor die rather than with discretes. If used with discretes, it is probably a specialty logic case. All three terminations can be found in differential interfaces as part of split termination.

RF Termination

The use of RF termination essentially involves the placement of filters at the output of a driver or at the input of a receiver/load such that the output impedance from a source hits a target impedance. RF impedance matching circuits should ideally have zero resistance, meaning they should only use reactive components. The reason is that we would prefer to not lose any power as a signal interacts with the impedance matching network.

Resistors are broadband terminating components, therefore we want to use them with broadband signals like digital signals. Reactive impedance matching networks produce impedance matching only within a certain bandwidth:

  • Reactive components termination circuits create high-Q or low-Q passbands
  • Multiple reactive components can be combined in stages to produce higher order filters
  • Some circuits will have ripple in their passband, which depends on the termination network topology

Another method that does not involve the use of discretes is the use of transmission line sections. These sections only apply impedance matching in very high-Q bandwidths and are best used with harmonic signals. To see why these points are important, read the links below.

Above a few GHz, termination with discrete components will not function as designed due to the presence of parasitics. This is why components operating at many GHz tend to place impedance matching elements directly on the semiconductor die so that output pins will match directly to 50 Ohms. Up to a few GHz, the placement and values used in discrete components needs to be simulated and measured.

SIM card holder and antenna on a green PCB

No matter what type of impedance matching or termination method you need to design, you can create circuits and design PCBs with the industry’s best electronics design features in Altium Designer®. To implement collaboration in today’s cross-disciplinary environment, innovative companies are using the Altium 365 platform to easily share design data and put projects into manufacturing.

We have only scratched the surface of what’s possible with Altium Designer on Altium 365. Start your free trial of Altium Designer + Altium 365 today.

About Author

About Author

Zachariah Peterson has an extensive technical background in academia and industry. He currently provides research, design, and marketing services to companies in the electronics industry. Prior to working in the PCB industry, he taught at Portland State University and conducted research on random laser theory, materials, and stability. His background in scientific research spans topics in nanoparticle lasers, electronic and optoelectronic semiconductor devices, environmental sensors, and stochastics. His work has been published in over a dozen peer-reviewed journals and conference proceedings, and he has written 2500+ technical articles on PCB design for a number of companies. He is a member of IEEE Photonics Society, IEEE Electronics Packaging Society, American Physical Society, and the Printed Circuit Engineering Association (PCEA). He previously served as a voting member on the INCITS Quantum Computing Technical Advisory Committee working on technical standards for quantum electronics, and he currently serves on the IEEE P3186 Working Group focused on Port Interface Representing Photonic Signals Using SPICE-class Circuit Simulators.

Related Resources

Related Technical Documentation

Back to Home
Thank you, you are now subscribed to updates.