Avoid BOM Stock, Cost And Lifecycle Surprises As You Design

Altium Designer

| Created: March 15, 2021

Surprises can be fun. Surprise parties, surprise gifts, and possibly surprise visits (depending on whom). Supply chain surprises on the other hand are no fun at all; they can derail your budget, deadlines, and build quality.

When electronic components become obsolete, design and production can suffer lengthy delays. With an average of 15 end-of-life notices issued every day, part obsolescence is a challenge that most engineers routinely face.

Watch this video to learn about:

Introduction to IHS MarkitⓇ
Component supply information
Lifecycle status
Locate obsolete components in completed projects
Component replacement

If you are interested in experiencing the world's finest PCB design product for yourself, request your free trial today and see why more Engineers and Designers choose Altium Designer than any other product available!

Would you like to find out more about how Altium Designer can help you with your next PCB design? Talk to an expert at Altium.

About Author

About Author

PCB Design Tools for Electronics Design and DFM. Information for EDA Leaders.

More content by Altium Designer

Recent Articles

Getting Started with MQTT

Getting Started with MQTT Check this out. This is a new project overview demonstrating MQTT by expert Ari Mahpour. In this article, Ari answers the What and Why of MQTT, and gives guidelines to get your project started. Read Article

2-layer PCB Routing

Can You Route Digital Signals on a 2-layer PCB? 2-layer PCBs are a common entry-level choice for designers, and they can even support high speed designs if built correctly. Read Article

Deterministic Solutions to Solve Skew Problems

Deterministic Solutions to Solve Skew Problems Avoid getting your design "skewed"! Today's guest is Z-Zero's Founder and CEO, Bill Hargin. Together we will dive into the cause of getting skews in your board. Watch now to get answers to your "skews" questions. Read Article

4-layer circuit board stackup

Two Alternative 4 Layer PCB Stackups With 50 Ohms Impedance Need a 4-layer PCB stackup that can support high speed components on both sides of the board? Consider these alternatives to the typical 4-layer stackup. Read Article

Finger touching screen

Design to Manufacturing with a Single Mouse Click Imagine if you could design your circuit board, run simulations, source your parts, generate an accurate BOM, generate your output files and simply press a “send to manufacturing” button all within your design environment? While that may sound like a far-off dream, this interview with Misha Govshteyn from Macrofab will give you insight into how they are partnering with Altium to make this dream a reality very soon. Judy Warner: Misha, please Read Article

microstrip to ground clearance

Microstrip Ground Clearance Part 2: How Clearance Affects Losses In a previous article, I provided a discussion and some simulation results on the necessary clearance between impedance controlled traces and nearby grounded copper pour. What we found was that, once the spacing between the pour and the trace becomes too small, the trace becomes an impedance-controlled coplanar waveguide (with or without ground). We also saw that the 3W rule for the spacing between the trace and the grounded copper pour is a bit Read Article

Differential Pairs and Differential Signals

What Are Differential Pairs and Differential Signals? Differential pairs and differential signals are the mainstay of high speed digital communication and data transfer. Read Article

what is signal integrity

What is Signal Integrity? Learn about the basics of signal integrity and how you can ensure your PCB layout complies with best practices for signal integrity. Read Article

MCAD CoDesigner - Rejection Comments

MCAD CoDesigner - Rejection Comments MCAD CoDesigner now displays the complete history of accepted and rejected changes, along with any comments the engineer has entered if a change is rejected. The history of changes is shown in MCAD CoDesigner's panel, making the interaction between the electrical and mechanical engineers more transparent. As soon as changes are applied/rejected on one side, the engineer on the other side is notified, and any rejection comments are displayed Read Article

ISM Bands Around the World

ISM Bands Around the World ISM bands (industrial, scientific, and medical) are parts of the RF (radio-frequency) spectrum reserved for general use by, as the name suggests, scientific, medical, and industrial devices. Their creation was in response to specific demands by these industries for access to the RF spectrum to perform functions without having to compete with the traditionally intensive users of RF, the communications, and defense sectors. The critical thing to Read Article

Back to Home