Multiboard Design for Assembly: Form, Fit and Build - OnTrack

Created: August 9, 2018
Updated: March 16, 2020

When doing PCB Design for a Multiboard Assembly, it is important to ask yourself, how is this multi board assembly actually going to be pieced together in the final assembly?

In this Episode of the OnTrack Whiteboard Series, Ben Jordan shares valuable tips and tricks about form, fit and build for Multi-board Assembly.

Watch and comment on this video below.

Learn How Altium Supports PCB Designers

Related Resources

How to Become a PCB Designer in Today’s World The electronics industry is facing a talent gap. As senior designers retire, companies are scrambling to find skilled professionals who understand modern hardware development. This isn't just about drawing lines; it's about architecting the physical nervous system of AI, EV, and IoT devices. Whether you are looking for a 3D PCB design software free download to start learning, or you are an experienced hardware engineer looking to specialize, the Read Article

What is an Engineering Bill of Materials in Agile PCB Design? Why do you need an engineering bill of materials as part of your agile PCB design workflow? Here’s how you can make sense of your system with an EBOM. Read Article

Flexible Circuit Base Materials Question: As someone new to designing with flex materials, what is important to understand about the base materials? For people new to calling out flex materials, it can be a little intimidating. Just like their rigid material counterparts, there are so many options to choose from, it can be mind-boggling. But, also just like their rigid material counterparts, once you learn the “basics”, most designs will fit within common parameters. Once those Read Article

Coverlay Type Driven by Installation and End Use Requirements Question: Should I use polyimide coverlay, or flexible solder mask? The fundamental purpose of either flexible solder stop mask or polyimide coverlay is no different than rigid solder mask. It is needed to encapsulate and protect the external circuit layers. But, when moving to a flexible circuit design the bending, folding and flexing requirements of the circuit in assembly and end use most often dictate which materials are recommended to Read Article

SAP and mSAP in Flexible Circuit Fabrication Question: What is SAP and mSAP? This is an excellent question. These acronyms are getting a lot of attention lately and are relatively new acronyms for the PCB industry, which ironically is infamous for using them. SAP and mSAP are not new terms to the electronics industry, they are common processes in IC substrate fabrication, but these are processes that are emerging technology in the PCB fabrication segment. After saying this is new technology Read Article

Rigid Outer-Layers to Reduce Cost Why is a 4-layer Rigid Flex Less Expensive than 3-layer Rigid Flex? Designing flex and rigid-flex can be tricky. Not only do you need to design for a product that will bend, fold and flex, you are working with different materials and fabrication processes. Plusm it is difficult to clearly communicate how the part should flex in final application. Typically, the goal is to use the most cost-effective stack up that meets both your electrical and Read Article

Budgetary Quote Early in the Design Process New products that will be produced in high volumes always start with a prototype, and multiple boards will end up being built throughout the product design and development process. Costs involved have to be scrutinized along the way and at each stage in prototyping, and one way to do this is to request a budgetary quote for your design. Budgetary quotes provide an estimate for procuring the PCB, assembly services, and the parts in the assembly Read Article

Why Doesn’t Every Application Use Rigid Flex Technology? Why Doesn’t Every Application Use Rigid Flex Technology? Good Question! Rigid-flex technology is a hybrid between rigid boards and flexible circuits,m combing the most favorable aspects of both. The flexible portion helps solve space, weight, and packaging issues because it can bend, fold, and flex in either installation (flex to install) or end use (dynamic flex). The rigid portion supports dense component areas, allowing higher layer counts Read Article

Rigid-Flex Prototyping Tips Question: What are a few key tips for flex and rigid-flex prototyping? My answer to this question is simple: OVER COMMUNICATE with your fabricator! Typically, prototypes are needed quickly, yet approximately 75%-80% of new part numbers go on hold for engineering questions and clarifications. This can have a significant impact on scheduling. Before you can work on ways to communicate clearly with your fabricator, you need to select the right Read Article

Rigid Flex Cost Comparison Are you starting a design and contemplating whether to use a rigid-flex construction or to move forward with multiple rigid boards and wire/cable connections? Using a rigid-flex concept to replace the traditional approach of using cable assemblies to join two or more rigid boards has clear benefits: reduction in space and weight, more design freedom in packaging, reliability, and increased current carrying capabilities. But the rigid-flex Read Article

Back to Home