Editorial credit: Aija Lehtonen / Shutterstock.com
A couple of weeks ago I attended a concert that was a tribute to the big band leader Stan Kenton. I love big band jazz for many reasons, one of which is the configuration of musicians and instruments in the band. There are usually around 15 to 20 musicians on different instruments, and everyone plays a different part. If just one person makes a mistake, it can ruin the balance of the number that was so carefully arranged by the composer.
The importance of each member of the band playing harmoniously together reminded me of the importance of a correctly manufactured printed board. If just one part isn’t soldered correctly, the finished board may have intermittent failures, or perhaps not work at all. Just as a saxophone playing a sour note can ruin the whole number, a bad solder joint can ruin the entire board. Fortunately, design for manufacturing (DFM) rules can help you to avoid hitting sour solder joints on your board.
One area where DFM rules can help your board may come as a surprise. How you route traces on your PCB can have a direct effect on solder problems, and DFM rules offer some guidance there. Take a look with me now at how trace routing can cause problems like cold solder joints or tombstoning so that you will know what to avoid in the future.
Acute angle traces
The first problem that we’ll look at is acute angle traces. Although this situation doesn’t specifically lead to a solder problem, it is a routing problem noted in PCB DFM guidelines.
Acute angles in traces are traces which have corners that are greater than 90 degrees. This causes the trace to come back on itself. The wedge that is created by the acute trace angle can trap acidic chemicals during the fabrication process. These trapped chemicals don’t always get cleaned up as they should during the cleaning phase of fabrication and will further eat away at the trace. This can eventually result in the trace breaking or cause intermittent connections.
Trace routing on a PCB
Tombstoning due to trace widths
Tombstoning happens when a small two pin part, such as a surface mount resistor, stands up on end on one of its pads during soldering. This results from a heating imbalance between the two pads during solder reflow. Whichever side melts first pulls the part towards that side, and causes the tombstoning effect.
One of the factors that can cause this heating imbalance is using different sized traces on the two pads. The wider the trace, the longer it will take for the pad that it is connected to heat up. If one pad of the part has a very narrow trace, and the other pad has a very wide trace, you will likely have a solder reflow imbalance and one pad will melt and reflow before the other one.
Often electrical engineering will want a power trace that is too wide for the manufacturer to reliably solder. PCB design for manufacturing guidelines have recommendations for the minimum and maximum trace widths to use on different sized , but that might not solve your problem. The key for you is to balance the requirements of both electrical engineering and manufacturing and come to a agreement between the two. In this way, you can meet the needs of both sides on your design.
DFM rules can help you to design out manufacturing problems on your board
Cold solder joints
Another problem that can happen when routing thicker traces is the creation of a cold solder joint. A cold solder joint is one where the solder has not reflowed correctly to make a good connection, or that the solder has pulled away from the connection. When routing a thick trace out of a pad, the thick trace size may end up pulling the solder off of the pad where it is needed to make the connection to the part.
The solution is to use traces widths that are smaller than the pad size. Some DFM guidelines recommend a trace no wider than 0.010 mils, although this again must be worked out to balance the needs of both electrical and mechanical engineering.
There is a lot more to PCB design for manufacturing guidelines than the trace routing recommendations that we have given you here. DFM guidelines will also help you with proper component placement techniques, footprint sizes, and other aspects of your design. This will ultimately help your design to be manufactured with as few errors as possible. A board that is error free during manufacturing is a reflection of a good and solid design, kind of like hearing the Stan Kenton band playing an error-free rendition of Intermission.
PCB design software, like Altium Designer®, has advanced routing capabilities and other features to better help you to design according to your DFM rules. This will help you to deliver a design that is DFM compliant to your manufacturer the first time.
Would you like to find out more about how Altium can help you with your next design to assure its DFM compliance? Talk to an expert at Altium.
About the AuthorVisit Website More Content by Altium Designer