RF and Microwave PCB Design Part 2- Transmission Lines and Impedance - OnTrack Whiteboard Series

Created: January 9, 2020
Updated: March 16, 2020

Learn How Altium Supports PCB Designers Start Your Design with Verifiable Requirements Unify Your Entire Design Workflow Share Version-Controlled Release Packages

Related Resources

Menu Changes and Switching Units in Altium Designer When I was a kid, the one place I always felt safe and secure was at home. Regardless of what happened outside, my childhood home was my refuge and I wanted to live there with my parents forever. Of course, as I grew older, I longed to do new things, meet new people, and have new experiences, but to do so meant changing where I lived. Just as I had to embrace change to grow as a person, it is sometimes necessary to make changes in order to Read Article

Switching Units From MM to Mils and Other PCB Design Measurement Preferences Your PCB layout needs to be an accurate reflection of your final design and should follow a specified unit scale. Inside Altium Designer, there are simple ways to set units as you work on the PCB layout, as well as in the schematic where circuits are being created. The short guide below shows how to switch from mm to mil in the Schematic Editor and in the PCB Editor. Users can do this live (while working on the PCB layout) or from the Preferences Read Article

Getting Started in Altium Designer: The Schematic A schematic is a way to record an idea. Schematics are drawings or diagrams that are used to communicate electronic ideas to others. You may have never thought about it, but anyone who understands electronics can look at your schematic and understand your idea, no matter what language they speak! Schematics are a universal “language” for recording and sharing electronic ideas. Here’s the official definition from IPC-T-50 (Terms and Definitions) Read Article

Even Simple Schematic Diagram Drawing Software is Better than Pencil and Paper

Even Simple Schematic Drawing Programs are Better than Pencil and Paper My mother used to clean all of her dishes in the sink with soap and water, and then put them in the dishwasher to finish the job. Perhaps when she was young those older dishwashers weren’t as good at cleaning dishes as they were later on. Years later when I was married and was cleaning up the kitchen, my wife looked at me as if I had lost my mind. “Why are you doing the same job twice,” she asked? It was the way that I had always done it, of Read Article

Getting Started in Altium Designer | Changing the Rules! The Altium Designer environment is controlled by rules, which are created using a powerful tool called the “PCB Rules and Constraints Editor”. By creating rules before component placement and routing starts, Altium can warn you or prevent you from making mistakes, depending on how your preferences are set. If rules are changed midstream, Altium’s sophisticated Design Rule Checker can highlight violations based on the revised rules, and report Read Article

PCB Design Process: The EDA Design Approach Streamline your PCB design process with EDA. Align requirements, schematic, layout, and release to cut respins and boost first-pass yield. Read Article

Linear Voltage Regulator vs switching regulator

Using LDOs vs Switching Regulators in Your PCB Designing a low power device? Learn more about the tradeoffs between LDOs vs switching regulators in this article. Read Article

The Peak of Engineering Efficiency is Now Available in Altium Designer 17

The Peak of Engineering Efficiency and PCB Design Technology is Now Available in Altium 17 The engineering mentality is one focused on efficiency and creativity. And whether you’re designing electronics in today’s autonomous vehicles or connected devices, the careful balance between art and science walks a very thin line. Sooner or later, you’re bound to hit a roadblock. Not in your ideas, but in executing those ideas efficiently in your tools

Read Article

For Your DC Power Application, Which Switching Power Supply Topology is Right? With so many switching power supply topologies to choose from, how do you pick the right one? This article gives a guide on switching power supply topologies. Read Article

Maximizing PCB Cooling with Best Design Practices for Surface Mount Heat Sinks

Heat Sink PCB Mounting: Maximizing Cooling with Best Design Practices for a Surface Mount Image Source: Flickr user bengt-re ( CC BY 2.0) Just How Important Are Heat Sinks? It’s a hot summer day in smoggy Brooklyn… Your fan is in an awkward spot in your overcrowded apartment and you can’t shake the heat. If only you could restructure your apartment’s layout so that the fan is blowing air in your direction to cool you down. The same can be said for your printed circuit board heat sink design if your surface mount technology (SMT) heat Read Article

RF and Microwave PCB Design Part 2- Transmission Lines and Impedance - OnTrack Whiteboard Series

Related Resources

Related Technical Documentation

Multidisciplinary Product Creation