When you create a design with an analog filter, it’s almost always static. You can’t change things like bandwidth, corner frequency, passband behavior, or pole-zero behavior without complex external circuitry. Typically, this requires a set of DAC channels that are controlled or modulated in the device firmware, or a fully analog approach can be taken with voltage-controlled discrete semiconductors. Things can get even more complex when switches and multiplexers are used to swap between passive components used in feedback networks.
Although these circuits can sometimes be difficult to engineer, they are very useful when capturing signals over a broad frequency range that requires adjustments to the filtering performance. The design task is to establish how frequency, bandwidth, and gain should change together. This article examines the available tuning methods, their application constraints, and a compact implementation using programmable analog resources in GreenPAK.
An analog filter becomes tunable when an electronically adjustable element replaces a fixed component that determines its frequency response. For example, in a simple RC filter, the corner frequency is 1/(2πRC), so doubling either resistance or capacitance halves the corner frequency. Electronic control of those component values allows firmware or an analog control signal to adjust the filter.
Three common implementations provide this adjustment:
A digital potentiometer acts as a frequency-setting resistor. For example, in an active low-pass filter, this programmable resistance and fixed capacitors enable an adjustable cutoff frequency. This would then be controlled by firmware in an MCU, which changes the resistance through a serial interface, moving the cutoff in discrete steps. The available resistance range sets the nominal tuning range, while resistance resolution determines the spacing between frequency settings.
These components offer creative ways to select between different groups of passive components. For example, the firmware can be used to trigger switching between different capacitor banks, resistor banks, or other discrete component values. For op-amp based circuits relying on a fixed reference voltage, it is possible to change between different reference sources with a digitally-controlled switch.
Effectively, each switch state produces a different frequency response, making this approach suitable for predefined operating bands, but it is not suitable for cases where smooth changes in the filtering action are desired.
These components provide continuously variable tuning of circuit element values within a filter circuit and are an analog solution. For example, a reverse-biased varactor replaces part of the capacitance in an LC resonator, and a DAC changes its bias voltage. When the inductance is fixed, increasing the total capacitance lowers the resonant frequency according to f₀ = 1/(2π√LC). A digitally adjustable regulator (normally controlled with a digital potentiometer int he feedback loop) can supply this bias.
All higher-order filters involve two or more frequency dependent components, which produce the higher-order rolloff seen in a transfer function. Coordinated adjustment of multiple components can preserve the shape of the transfer function as the frequency changes. For example, scaling both frequency-setting resistances in a Sallen-Key stage by the same factor shifts its natural frequency while preserving the filter’s Q value. There are many other examples of mixed parameter adjustments which can hold gain and/or phase at constant value as the frequency response changes.
A big challenge with tunable filters is that they require a large number of components, ranging from sets of passives and discrete semiconductors to many integrated circuits. With op amp solutions, the op amp stage alone could involve multiple op amp chips connected together in various ways. The easiest way to consolidate all of this circuitry into a single component is with GreenPAK mixed-signal processors from Renesas.
As an example of what’s possible in GreenPAK, a second-order Sallen-Key low-pass filter can be implemented using the integrated op-amps and digital rheostats in SLG47004V. The two rheostats provide adjustable resistances that control the filter’s cutoff frequency. OPAMP0 forms the active filter stage, while OPAMP1 buffers the input. External capacitors and feedback resistors complete the circuit.
The digital rheostats and op-amps used in this circuit are configurable, and additional external components can be used to set up the Sallen-Key frequency response. This component’s I2C interface allows the system host to update the rheostat registers and thus change the cutoff frequency.
The advantage of using GreenPAK is not just the reconfigurability of the frequency response setpoints in these components. GreenPAK devices can aggregate multiple capabilities into one IC across sensor interfaces, power systems, and many other types of designs. Such features include:
The Go Configure development suite allows engineers to configure comparator thresholds, qualification logic, delays, and output behavior. Simulation and development hardware support evaluation of the resulting sequence, including early requests and interrupted settling. Device selection depends on the analog resources, timing blocks, and pins required for each independently controlled enable output.
To learn more, take a look at the GreenPAK components and reference examples.
Whether you need to build reliable power electronics or advanced digital systems, use the complete set of PCB design features and world-class CAD tools offered by Altium to implement your GreenPAK solutions. Altium provides the world’s premier electronic product development platform, complete with the industry’s best PCB design tools and cross-disciplinary collaboration features for advanced design teams. Contact an expert at Altium today!